東華大學圖書館 |

Language: English

Help

回圖書館首頁

手機版館藏查詢

Back

Switch To: Labeled | MARC Mode | ISBD

Mag-microbots: Design, modeling, and...

Floyd, Steven Richard Charles.

Linked to FindBook

Google Book

Amazon

博客來

Mag-microbots: Design, modeling, and implementation of an untethered magnetically controlled micro-robotic system.

Record Type:	Language materials, printed : Monograph/item
Title/Author:	Mag-microbots: Design, modeling, and implementation of an untethered magnetically controlled micro-robotic system./
Author:	Floyd, Steven Richard Charles.
Description:	220 p.
Notes:	Source: Dissertation Abstracts International, Volume: 71-05, Section: B, page: 3326.
Contained By:	Dissertation Abstracts International71-05B.
Subject:	Engineering, Electronics and Electrical. -
Online resource:	http://pqdd.sinica.edu.tw/twdaoapp/servlet/advanced?query=3410257
ISBN:	9781124008486

Mag-microbots: Design, modeling, and implementation of an untethered magnetically controlled micro-robotic system.
Floyd, Steven Richard Charles.

Mag-microbots: Design, modeling, and implementation of an untethered magnetically controlled micro-robotic system. - 220 p.

Source: Dissertation Abstracts International, Volume: 71-05, Section: B, page: 3326.

Thesis (Ph.D.)--Carnegie Mellon University, 2010.

Though several miniature robots currently exist at the centimeter size scale, true micron-scale robots, with all characteristic lengths on the order of tens to hundreds of microns, are still quite rare. The fundamental challenge with decreasing robot size below the centimeter scale is providing power and actuation to the device. To address this challenge, this thesis presents the design and implementation of a novel micro-robotic system that uses macro-scale electromagnets for actuation of a micro-scale permanent magnet, which acts as an untethered end-effector. System design, capabilities, and limitations are explored with regard to the control of the end effector, or micro-robot, and its ability to operate and interact within its environment.

ISBN: 9781124008486Subjects--Topical Terms:

626636
Engineering, Electronics and Electrical.

Mag-microbots: Design, modeling, and implementation of an untethered magnetically controlled micro-robotic system.
LDR:03188nam 2200289 4500 001 1394236
005 20110506085310.5
008 130515s2010 ||||||||||||||||| ||eng d
020 $a 9781124008486
035 $a (UMI)AAI3410257
035 $a AAI3410257
040 $a UMI $c UMI
100 1 $a Floyd, Steven Richard Charles. $3 1672840
245 1 0 $a Mag-microbots: Design, modeling, and implementation of an untethered magnetically controlled micro-robotic system.
300 $a 220 p.
500 $a Source: Dissertation Abstracts International, Volume: 71-05, Section: B, page: 3326.
502 $a Thesis (Ph.D.)--Carnegie Mellon University, 2010.
520 $a Though several miniature robots currently exist at the centimeter size scale, true micron-scale robots, with all characteristic lengths on the order of tens to hundreds of microns, are still quite rare. The fundamental challenge with decreasing robot size below the centimeter scale is providing power and actuation to the device. To address this challenge, this thesis presents the design and implementation of a novel micro-robotic system that uses macro-scale electromagnets for actuation of a micro-scale permanent magnet, which acts as an untethered end-effector. System design, capabilities, and limitations are explored with regard to the control of the end effector, or micro-robot, and its ability to operate and interact within its environment.
520 $a Actuation of the micro-robot is based upon a stick-slip type motion and is achieved in several environments, including vacuum, air, and liquid. By pivoting the micro-robot about an edge, movement over large, non-planar obstacles with characteristic sizes comparable to the micro-robot's length is possible. Manipulation of micro-scale objects in both water and silicone oil is demonstrated in two ways: contact and non-contact pushing modes. Contact manipulation is based on the micro-robot physically pushing the micro-objects while non-contact manipulation relies on the fluid flow generated by micro-robot's motion.
520 $a Simultaneous control of multiple devices is achieved in two different ways with both homogeneous and heterogeneous groups of micro-robots. First, by designing individuals to respond uniquely to the same input magnetic fields, those fields are used as selection methods for individuals or small groups to locomote in a parallel fashion. A second method employs an array of individually addressable electrostatic surfaces to selectively anchor individual micro-robots. Coupled parallel and uncoupled serial motion of multiple devices is demonstrated in both cases, and individuals are shown capable of combining to form assemblies that are also capable of motion and micro-object manipulation. Models based on the magnetic, fluidic, electrostatic and surface forces and the various physical phenomena are developed and used to create a dynamic simulation to explain and predict the micro-robot's experimental behavior.
590 $a School code: 0041.
650 4 $a Engineering, Electronics and Electrical. $3 626636
650 4 $a Engineering, Mechanical. $3 783786
650 4 $a Engineering, Robotics. $3 1018454
690 $a 0544
690 $a 0548
690 $a 0771
710 2 $a Carnegie Mellon University. $3 1018096
773 0 $t Dissertation Abstracts International $g 71-05B.
790 $a 0041
791 $a Ph.D.
792 $a 2010
856 4 0 $u http://pqdd.sinica.edu.tw/twdaoapp/servlet/advanced?query=3410257