東華大學圖書館 |

Language: English

Help

回圖書館首頁

手機版館藏查詢

Back to Search results for [ null ]

Switch To: Labeled | MARC Mode | ISBD

Textures, microstructures, anisotrop...

Liu, Jiantao.

Linked to FindBook

Google Book

Amazon

博客來

Textures, microstructures, anisotropy and formability of aluminum-manganese-magnesium and aluminum-magnesium alloys.

Record Type:	Electronic resources : Monograph/item
Title/Author:	Textures, microstructures, anisotropy and formability of aluminum-manganese-magnesium and aluminum-magnesium alloys./
Author:	Liu, Jiantao.
Description:	275 p.
Notes:	Source: Dissertation Abstracts International, Volume: 64-05, Section: B, page: 2346.
Contained By:	Dissertation Abstracts International64-05B.
Subject:	Engineering, Materials Science. -
Online resource:	http://pqdd.sinica.edu.tw/twdaoapp/servlet/advanced?query=3092317

Textures, microstructures, anisotropy and formability of aluminum-manganese-magnesium and aluminum-magnesium alloys.
Liu, Jiantao.

Textures, microstructures, anisotropy and formability of aluminum-manganese-magnesium and aluminum-magnesium alloys. - 275 p.

Source: Dissertation Abstracts International, Volume: 64-05, Section: B, page: 2346.

Thesis (Ph.D.)--University of Kentucky, 2003.

In this dissertation work, the microstructure and texture evolution of continuous cast (CC) and direct chill (DC) cast Al-Mn-Mg (AA 3105 and AA 3015) and Al-Mg (AA 5052) alloys during cold rolling and annealing are systematically investigated. Macrotexture analyses were based on three-dimensional orientation distribution functions (ODFs) calculated from incomplete pole figures from X-ray diffraction by using arbitrarily defined cell (ADC) and series expansion methods. A new technique, electron backscatter diffraction (EBSD), was adopted for microtexture and mesotexture investigation. The anisotropy and formability of Al-Mn-Mg and Al-Mg alloys are correlated to the texture results.Subjects--Topical Terms:

1017759
Engineering, Materials Science.

Textures, microstructures, anisotropy and formability of aluminum-manganese-magnesium and aluminum-magnesium alloys.
LDR:03878nmm 2200313 4500 001 1864443
005 20041216132046.5
008 130614s2003 eng d
035 $a (UnM)AAI3092317
035 $a AAI3092317
040 $a UnM $c UnM
100 1 $a Liu, Jiantao. $3 1951936
245 1 0 $a Textures, microstructures, anisotropy and formability of aluminum-manganese-magnesium and aluminum-magnesium alloys.
300 $a 275 p.
500 $a Source: Dissertation Abstracts International, Volume: 64-05, Section: B, page: 2346.
500 $a Director: James G. Morris.
502 $a Thesis (Ph.D.)--University of Kentucky, 2003.
520 $a In this dissertation work, the microstructure and texture evolution of continuous cast (CC) and direct chill (DC) cast Al-Mn-Mg (AA 3105 and AA 3015) and Al-Mg (AA 5052) alloys during cold rolling and annealing are systematically investigated. Macrotexture analyses were based on three-dimensional orientation distribution functions (ODFs) calculated from incomplete pole figures from X-ray diffraction by using arbitrarily defined cell (ADC) and series expansion methods. A new technique, electron backscatter diffraction (EBSD), was adopted for microtexture and mesotexture investigation. The anisotropy and formability of Al-Mn-Mg and Al-Mg alloys are correlated to the texture results.
520 $a For aluminum alloys studied in this work, a stronger Cube orientation is observed in DC hot band than in CC hot band after complete recrystallization. alpha and beta fibers become well developed beyond 50% cold rolling in both CC and DC aluminum alloys. The highest intensity along the beta fiber (skeleton line) is located between the Copper and the S orientations in both materials after high cold rolling reductions. In both CC and DC aluminum alloys, a cell structure develops with the indication of increasing CSL Sigma1 boundaries during the early stages of cold rolling. There is no evidence of the development of twin boundaries (Sigma3, Sigma9, Sigma27a & 27b) in either CC or DC aluminum alloys when the cold rolling reductions are less than 40%.
520 $a The R and Cube textures are dominant recrystallization texture components in CC and DC AA 5052 alloys. The volume fraction of the Cube component is increased by increasing cold rolling reduction and annealing temperature but not by increasing annealing time while the volume fraction of the R component is only increased by increasing cold rolling reduction. Stronger Cube and R orientations are found at the surface layer than at half-thickness layer of cold rolled hot bands after annealing.
520 $a The Cube and P textures are dominant recrystallization texture components in DC AA 3105 and CC AA 3015 alloys, respectively. When the hot bands of CC AA 3015 alloy were directly cold rolled followed by annealing the P orientation {011}<566>, accompanied by the R-CubeND orientation {001}<130>, was found to be the major recrystallization texture component for CC AA 3015 alloy. The Brass orientation {011}<112> transforms to the P orientation along the alpha fiber during annealing. The intensity of the P orientation increases with increasing cold rolling reduction and the highest intensity is obtained utilizing a 450°C anneal. The Zener drag mechanism appears to be responsible for the formation of the highly RD-elongated recrystallized grain structure.
520 $a For CC AA3015 alloy, the yield strength and ultimate strength of cold rolled hot bands at O-temper condition can be significantly increased by solid solution annealing of hot bands before cold rolling.
590 $a School code: 0102.
650 4 $a Engineering, Materials Science. $3 1017759
650 4 $a Engineering, Metallurgy. $3 1023648
690 $a 0794
690 $a 0743
710 2 0 $a University of Kentucky. $3 1017485
773 0 $t Dissertation Abstracts International $g 64-05B.
790 1 0 $a Morris, James G., $e advisor
790 $a 0102
791 $a Ph.D.
792 $a 2003
856 4 0 $u http://pqdd.sinica.edu.tw/twdaoapp/servlet/advanced?query=3092317