東華大學圖書館 |

Language: English

Help

回圖書館首頁

手機版館藏查詢

Back to Search results for [ null ]

Switch To: Labeled | MARC Mode | ISBD

Mechanical properties of whey protei...

Simelane, Sindisiwe N.

Linked to FindBook

Google Book

Amazon

博客來

Mechanical properties of whey protein isolate-based edible films as affected by meat processing conditions and optimization of these properties.

Record Type:	Electronic resources : Monograph/item
Title/Author:	Mechanical properties of whey protein isolate-based edible films as affected by meat processing conditions and optimization of these properties./
Author:	Simelane, Sindisiwe N.
Description:	111 p.
Notes:	Source: Masters Abstracts International, Volume: 42-06, page: 2073.
Contained By:	Masters Abstracts International42-06.
Subject:	Agriculture, Food Science and Technology. -
Online resource:	http://pqdd.sinica.edu.tw/twdaoapp/servlet/advanced?query=1420001
ISBN:	0496247534

Mechanical properties of whey protein isolate-based edible films as affected by meat processing conditions and optimization of these properties.
Simelane, Sindisiwe N.

Mechanical properties of whey protein isolate-based edible films as affected by meat processing conditions and optimization of these properties. - 111 p.

Source: Masters Abstracts International, Volume: 42-06, page: 2073.

Thesis (M.S.)--Michigan State University, 2004.

This study was conducted to test the hypothesis that whey protein isolate (WPI)-based edible films could be used as sausage casings comparable to collagen casings. Heat cured (80°C, 24 h or 90°C, 12 h) WPI-based films containing glycerol and candelilla wax were treated under meat processing conditions; the effects of temperature, time and relative humidity on the tensile strength (TS) and percent elongation (%E) of the films were determined. Tensile strength of WPI-based films was lower while %E was similar to that of collagen films. To optimize the mechanical properties of the WPI-based films, different film forming solutions (5.8% or 6.4% w/v solids content), casting on different surfaces (anodized or non-anodized TeflonRTM), heat curing (90°C, 12 h) and compression molding (single- and double-stage; and varying temperature, pressure and time) were studied. Heat curing and compression molding increased TS and had no effect on %E. In a separate double-stage compression molding experiment, temperature, pressure and time conditions were optimized. No optimum combination of these conditions was obtained. Finally, seal strengths and surface chemistry (using electron spectroscopy for chemical analysis, ESCA) of unsealed and sealed uncured, heat cured and compression molded WPI-based films were studied. Uncured films had the highest seal strengths. Sealed, heat cured and compression molded films had a preponderance of C-O-H and C-O-C bonds, which were not detected in uncured films.

ISBN: 0496247534Subjects--Topical Terms:

1017813
Agriculture, Food Science and Technology.

Mechanical properties of whey protein isolate-based edible films as affected by meat processing conditions and optimization of these properties.
LDR:02421nmm 2200265 4500 001 1841740
005 20050915140308.5
008 130614s2004 eng d
020 $a 0496247534
035 $a (UnM)AAI1420001
035 $a AAI1420001
040 $a UnM $c UnM
100 1 $a Simelane, Sindisiwe N. $3 1930024
245 1 0 $a Mechanical properties of whey protein isolate-based edible films as affected by meat processing conditions and optimization of these properties.
300 $a 111 p.
500 $a Source: Masters Abstracts International, Volume: 42-06, page: 2073.
500 $a Adviser: Zeynep Ustunol.
502 $a Thesis (M.S.)--Michigan State University, 2004.
520 $a This study was conducted to test the hypothesis that whey protein isolate (WPI)-based edible films could be used as sausage casings comparable to collagen casings. Heat cured (80°C, 24 h or 90°C, 12 h) WPI-based films containing glycerol and candelilla wax were treated under meat processing conditions; the effects of temperature, time and relative humidity on the tensile strength (TS) and percent elongation (%E) of the films were determined. Tensile strength of WPI-based films was lower while %E was similar to that of collagen films. To optimize the mechanical properties of the WPI-based films, different film forming solutions (5.8% or 6.4% w/v solids content), casting on different surfaces (anodized or non-anodized TeflonRTM), heat curing (90°C, 12 h) and compression molding (single- and double-stage; and varying temperature, pressure and time) were studied. Heat curing and compression molding increased TS and had no effect on %E. In a separate double-stage compression molding experiment, temperature, pressure and time conditions were optimized. No optimum combination of these conditions was obtained. Finally, seal strengths and surface chemistry (using electron spectroscopy for chemical analysis, ESCA) of unsealed and sealed uncured, heat cured and compression molded WPI-based films were studied. Uncured films had the highest seal strengths. Sealed, heat cured and compression molded films had a preponderance of C-O-H and C-O-C bonds, which were not detected in uncured films.
590 $a School code: 0128.
650 4 $a Agriculture, Food Science and Technology. $3 1017813
690 $a 0359
710 2 0 $a Michigan State University. $3 676168
773 0 $t Masters Abstracts International $g 42-06.
790 1 0 $a Ustunol, Zeynep, $e advisor
790 $a 0128
791 $a M.S.
792 $a 2004
856 4 0 $u http://pqdd.sinica.edu.tw/twdaoapp/servlet/advanced?query=1420001